ISO 24410 PDF

ISO (E). PDF disclaimer. This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may. Name: ISO Description: Skid Steer Loaders – Coupling of Attachments. Official Title: Earthmoving Machinery – Coupling of Attachments to Skid. Buy NEN ISO EARTH-MOVING MACHINERY – COUPLING OF ATTACHMENTS TO SKID STEER LOADERS from SAI Global.

Author: Teshura Mazumi
Country: Moldova, Republic of
Language: English (Spanish)
Genre: Music
Published (Last): 7 September 2004
Pages: 148
PDF File Size: 1.13 Mb
ePub File Size: 12.82 Mb
ISBN: 602-9-74841-151-8
Downloads: 20616
Price: Free* [*Free Regsitration Required]
Uploader: Nikogul

By clicking the button below, you agree to the TractorByNet. We will not share your e-mail address with any other party for any reason.

Standards Catalogue

Homepage Today’s Posts Search. Page 1 of 2 1 2 Last Jump to page: Results 1 to 10 of Thread Tools Show Printable Version. Here is the Universal Attachment Mount Specification!

The specification actually describes the area that is reserved for the loader side of the attachment, which then tells you how to wrap an attachment mount around it.

Here is the Universal Attachment Mount Specification!

The SAE specification is Metric. The attached file has an additional image with all measurements converted to the nearest 16th inch. I was looking for that!

I’m also happy to see that, now I know the four I built are right!! Click here for my current weather Case C with dirt bucket, forks, 3 point quick hitch on the front, 30′. PDF files don’t like me!!

  CHONGQING MONORAIL PDF

Now I know why the one I built is a little hard to get on. I won’t make that mistake again. 2440 there such a specification sheet and or dimensions for category I 3 point hitch, quick attachments. If you were building another mount wouldn’t it be logical to copy the one you already have that fits correctly?

What you are missing is that when I built the Quick Attach receptacle I was somewhat handicapped in addition to the natural genetic ones. I did not have a QA loader or an attachment lso a QA receptacle. I just measured the QA locking section the one that connects to the FEL on a machine at a dealer’s lot and made a receptacle that I thought it would “fit” into. And the receptacle could not be made in a single piece because part of the implement it was designed for protrudes between the two arms.

Therefore, it was in two pieces–sortaand then attached to the implement.

And my old tape measure may have been a bit off, to say nothing of the plastic protractor I used to 244100 the angles. Combine that with blurred vision and a shop so full izo junk iron I could hardly move, and it is a wonder it fit at all.

But on the next one I can just park the tractor in the shop with the FEL raised about 4′ and use the QA just like a tailor uses a mannikin to “mold” a suit, ‘scept I will weld where he sews.

  IEC 60034-3 PDF

Since I never seem to allow enough clearance for welding bead shrinkage and shrinkage of iron due to heating and cooling, it will probably fit so tight I will never get if off. I made a simple wooden pattern of jig of the portion that fits on the FEL. It is piece of plywood with a block of wood kso each corner.

ISO 24410:2005

The blocks hav ethe correct angle. I clamp this to the implement, then clamp oso strips of steel to the blocks and start welding. The blocks set the wor angles correctly, set the dimensions correct, and also ensure the mount is square.

With this setup it takes four strips of metal, a cutting torch, amd a welder to install a quich hitch to an implement with a flat surface. What would be really 244410 is to make the fixture out of steel, with magnets that would hold the four steel strips. All times are GMT The time now is Other trademarks on this page are the property of their respective owners.