BREMSHEY ORBIT PLUS MANUAL PDF

You can find the manual for your Bremshey Cross Trainer below. Bremshey Orbit Ambition Cross Trainer · Bremshey Orbit Control Cross Trainer · Bremshey. Check the reed sensor also known as the speed sensor. It is located on the front roller pulley. It is mounted to the frame and looks like a small. 18TSFC_Star Fit C HR i-Plus Crosstrainer_OMpdf . _Bremshey Orbit Ambition C_User Manual. pdf. MB.

Author: Mooguran Mikagor
Country: France
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 14 April 2017
Pages: 181
PDF File Size: 16.94 Mb
ePub File Size: 19.47 Mb
ISBN: 878-1-19607-427-2
Downloads: 35607
Price: Free* [*Free Regsitration Required]
Uploader: Shakami

These are often a source of noise or unsmooth operation and therefore attention is often required. The software will automatically detect the modification and function as per described in the chapters 1 – 5.

Manual – Bremshey Orbit Control Cross Trainer

Re-plug in the main power supply wire. When an error text occurs, the first thing to do, if not any obvious visible reasons found, is to try to repeat it after being switched off and on again.

Defective cable or connector between the user interface and lower board a. After belt manjal installed it will need to be lubed, tensioned, and the tracking checked.

Thereafter the console lights will flash indicating that the engineering mode has been entered. Only user interface parameters are valid within the limits 4. Check for interference from other electronic devices.

The securing nut a should be released and the adjusting nut turned to increase or decrease the tension of the cable. Be careful not to trap fingers at this point. This product therefore carries the CE label. Place a long drift through the centre hole of one bearing so that it rests against the inner side of the opposite bearing. LED scanning mode for verifying display functionality 3. As a general rule, when a source of malfunction is located, it should not be repaired, but instead replaced with a new component.

Before starting the update procedure make sure you have all the following: Points to check Stand tubes should be in correct orientation and alignment bolts inserted correctly coach head at base and tightened.

  JUICIO REIVINDICATORIO PDF

Repeat the removal process with the other side. First remove the servo-motor brake cable a from the flywheel brake mechanism.

Search results

Set calibration to minimum by turning blue trimmer clockwise 3. The cross frames often need to be replaced in this situation. Hold down ‘ZOOM’ —button and rotate selection wheel first 5 steps minimum counter-clockwise and then 5 steps clockwise.

Continue to rotate the drum whilst forcing the belt to remain in place with your hand. The circuit board can be replaced by removing 4 x screws fixing it to the frame l and unplugging the cables.

The software will use the calibration parameters read from the EEPROM and use them to control the electromagnetic brake without notifying anything to user. Slacken off the nylok nut on the non drive belt side of the flywheel axle by around 2 turns. Mahual primary intention of this Service Manual is to enhance the reader’s knowledge of the structures of the treadmills.

The error can only appear when voltage is supplied to the electromagnet. Install servo motor and switch off power 2. Both user interface and lower board has been replaced with bremdhey ones. Slacken off the vertical tensioning bar by loosening the upper and lower locking bolts f and then remove lower adjusting bolt g 2. While static shock problems are not specific to one particular make or brand manusl treadmill, we at Accell Fitness are always working to ensure our users experience a more comfortable workout, free of static shocks.

Check connection and restart PC if needed. The joint must be isolated to check its performance by either detaching the lower swing arm tube from the upper or detaching the foot-tube from the rear drum See earlier It is important that the combination of components is correctly assembled and adjusted.

For example, the pedal rotates once per revolution, should this be the frequency of the noise, the pedal needs to be tightened up. If treadmill recovers to normal operation, you may continu e to use the treadmill. Original parameters are written on label attached to the product frame post inside side covers. Details of the extractor adaptor tool The adaptor can be made by cutting a piece of 8 x 1.

  COURS ROUTEUR MIKROTIK PDF

Bremshey EMS x 2.

Use bolt- pt It can be made easier by removing the drive belt from the rear drum See section. The software will use the parameters from the EEPROM for controlling the electromagnetic brake and store them also to the user interface memory. The user interface msnual been orrbit with a new spare part.

We recommend that at this point the lower adjuster bolt is unscrewed, the spring that is sometimes located at the bottom of the vertical tensioning bar is removed, and the adjusting bolt re-fitted but not tightened.

Manuals for Bremshey Cross Trainers

Remove the circlip and washer located on the end of the axle projecting through the right side and then pull the left side unit away. In general, orbig to the transmission is gained by removing left covers and brake system requires right-hand. Action to rectify 1.

Before removing the covers from a machine powered by mains transformer it will be necessary to remove the power socket from the rear of the cover. Inside each swing arm joint there is a combination of a sealed bearing and sinter bearing.

The software will use the parameters from the EEPROM for controlling the electromagnetic brake but will not store them to user bremsyey memory. Please ensure that at this point the the belt remains on the resistance flywheel boss by observing its position during rotation.

“service manual”

This can also be used to lower lift motor if stuck in elevated position. Remove cap from the centre of the right-hand side drum cover. Replace the separating bush and then re-fit manuual bearing as above.

Withdraw complete foot tube and swing arm assembly away from drum. Resistance Mechanisms There are 3 types of brake control used.