ASTM D6110 PDF

Charpy for ASTM D and ASTM D Testing and Izod Impact Testers for ASTM D, ASTM D and ASTM E23 Testing. ASTM D defines the method used to determine the resistance of plastic to breakage when impacted in a three point bend configuration, using a pendulum. ASTM D is used to determine the resistance of plastics to breakage by flexural shock as indicated by the energy extracted from standardized pendulum type.

Author: Kazikazahn Tygozshura
Country: Martinique
Language: English (Spanish)
Genre: Love
Published (Last): 23 March 2017
Pages: 280
PDF File Size: 19.20 Mb
ePub File Size: 9.78 Mb
ISBN: 410-9-87649-498-3
Downloads: 99921
Price: Free* [*Free Regsitration Required]
Uploader: Kelkree

Loadframe, pendulum, supporting vice jaws, specimen centering plate, spanner, power cord, manual etc.

ASTM D6110

Glossary of Materials Testing Terms. If breakage does not occur, a heavier hammer is used until failure occurs. Supporting blade included angle.

The machines with pendulum-type hammers have been standardized in astmm they must comply with certain requirements including a ashm height of hammer fall, which results in a substantially fixed velocity of the hammer at the moment of impact. Impact resilience is one of the most important properties and cost-effective evaluations for material producers, both with respect to product development and quality control.

United Test product both the IZOD and Charpy impact tester, in dial display, LCD xstm display and computer control used determine the impact ductility of nonmetallic materials, such as Rigid thermoplastic and thermosetting plastic, thermosetting plastic and thermoplastic after fiber-reinforced. The notch in the specimen serves to concentrate the stress, minimize plastic deformation, and direct the fracture to the part of the specimen behind the notch.

  EIAJ RC-5320A STANDARD PDF

ASTM D6110 Charpy Impact Resistance of Notched Specimens of Plastics

Charpy and Izod Tests; IT30 0. Vibrational losses are observed when wide specimens of tough materials ashm tested in machines of insufficient mass, or in machines that are not securely fastened to a heavy base.

d611 The notch produces a stress concentration which promotes a brittle, rather than a ductile, fracture. The following testing parameters have been shown to affect test results significantly: The results are reported in terms of energy absorbed per unit of specimen width, or more specifically, the energy absorbed in breaking the specimen which is equal to the difference between the potential energy at the moment of impact and the residual energy. To fully understand the test set-up, procedure, results and specimen preparation requirements, please refer to the standard.

Significant energy losses due to bending and indentation when testing soft materials have also been observed.

The values obtained can be used for d1610 control or to differentiate general toughness. In both the Charpy and Izod Tests, the notch produces a stress concentration which promotes a brittle, rather than a ductile, fracture.

The hammer is released and allowed to strike through the specimen. Link to Active This link will always route to the current Active version of the standard.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The specimen is mounted horizontally and supported unclamped at both ends.

Note 3—Caution must be exercised in interpreting the results of this test method. This test method requires specimens to be made with a milled notch see Note 2. Or refer product link: Subscribe to Instron News!

  DVP615 MANUAL PDF

Charpy and Izod Impact Testers for ASTM D, D, D, ASTM D and ASTM E23

Historical Version s – view previous versions of standard. Izod Tests on plastics, ceramics, glass, etc. Moreover, manufacturers of the equipment are permitted to use different lengths and constructions of pendulums with possible differences in pendulum rigidities resulting see Section 5. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 4—This standard resembles ISO in title only. Note 1—The machines with pendulum-type hammers have been standardized in that they must comply with certain requirements including a fixed height of hammer fall, which results in a substantially fixed velocity of asttm hammer at the moment of impact.

ASTM D – Instron

The toss energy, or the energy used to throw the free ends of the broken specimen, is suspected to represent a very large fraction of the total energy absorbed when testing relatively dense and brittle materials. The notch produces a stress concentration which promotes a brittle, rather than a ductile, fracture. The pendulum is released and allowed to strike qstm the specimen. Onsite Training At Your Facility. One design of milled notch is allowed.