ASTM B505 PDF

ASTM B BM 08 Standard Specification for Copper Alloy Continuous Castings_机械/仪表_工程科技_专业资料。ASTM B BM Chemical Composition according to ASTM B/BM 1Ni value includes Co. Note: Cu + Sum of Named Elements, % min. Single values, unless. ASTM B/BM Standard Specification for Copper Alloy Continuous Castings. standard by ASTM International, 03/01/ View all product details.

Author: Nikotaur Mezinos
Country: Norway
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 6 February 2004
Pages: 198
PDF File Size: 3.67 Mb
ePub File Size: 17.99 Mb
ISBN: 137-6-31016-641-9
Downloads: 24529
Price: Free* [*Free Regsitration Required]
Uploader: Vudodal

C leaded tin bronze 88 6 1. Equivalent specifications are verified and updated annually. Request a Quote Metals: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Astm B SAE Bronze | Morgan Bronze Products, Inc.

C leaded tin bronze It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. When tolerances are speci? In such cases the manufacturer shall maintain heat traceability to speci? Approved April 1, Link to Active This link will always route to the current Active version of the standard.

G Iron content shall not exceed nickel content. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis. Actual sstm may vary by manufacturer.

ASTM B505 SAE 660 Bronze

C in the heat-treated condition will not be attained if the lead content exceeds 0. Continuous castings shall not be mechanically repaired, plugged, or burned in. Dimensions and Permissible Variations C tin bronze C bismuth tin bronze 89 Mechanical Property Requirements 8.

  APOSTILA MOLDFLOW PDF

C used only in the quench-hardened and tempered TQ30 condition. C high-leaded tin bronze 80 10 9. Your comments are invited either for revision asttm this standard or for additional standards and should be addressed to ASTM International Headquarters. The specimen shall be comprised of the following major elements: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The cross sections are the diameter of a round solid, the distance across the? C leaded semi-red brass 80 5 2. Each continuous casting from which the test bar was taken shall be identi?

Marking shall be in such a position as not to injure the usefulness of the casting. C nickel-tin bronze C copper-nickel-tin 85 If the wall thickness is 1? Historical Version s – view previous versions of standard.

ASTM B BM 08 Standard Specification for Copper Alloy Continuous Castings_百度文库

Each continuous cast bar from which the test bar was taken shall be identi? This leaded tin bronze, alloy C can be produced in 3 ways, continuous cast, centrifugal cast, or sand cast. C leaded nickel bronze Table 3 and Table 4 are to be used in conjunction with Tolerance Table 6 and Table 5, respectively. If all of the test bars from the initial sampling meet the requirements, the lot shall be acceptable. No further reproductions authorized. Our weights are conservative to the heavier side but there may be slight variations in weight from bar to bar.

  ASCO 8210G94 PDF

C leaded red brass This abstract is a brief summary of the referenced standard. At the request of the purchaser castings shall be marked with the alloy number.

Cooling shall be by the fastest means possible that will not cause excessive distortion or cracking. Specifications shown are current as of May 4, D Yield strength at 0.

Pressure-containing castings weighing less than 50 lb C Bronze Stock Allowances: Combining values astk the two systems may result in non-conformance with the standard. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

This standard has been approved for use by agencies of the Department of Defense. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.